Intermec PD41 User Manual Page 124
- Page / 162
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Appendix B — Default Settings
110 PD41 and PD42 Commercial Printer User’s Manual
Default Configuration
Use this appendix to view the default settings on the printer. If you
need to restore factory defaults at any time, you can use PrintSet or
the printer home page to reset the printer.
To reset the printer to factory defaults using Printset
• Use the Factory Default Wizard in the Printer Tasks box.
To reset the printer to factory defaults using the home page
1 From the home page, click Printer > Web Shell.
2 Click Default Setup.
3 When prompted, click OK. The printer defaults are restored.
4 Reboot the printer.
The following tables list the default values of the configuration
commands supported on the PD41 and PD42 printers. If you restore
the printer to factory default settings, these are the values it uses.
The commands are grouped by function and reflect the organization
of the IPL and Fingerprint setup menus. For detailed information on
most of the commands, see the Intermec Fingerprint Command
Reference Manual or the IPL Command Reference Manual.
IPL Default Configuration
Ser-Com Parameters
Parameter Default Value
Baud rate 9600
Data bits 8
Parity None
Stop bits 1
Protocol XON/XOFF
- PD41 1
- Document Change Record 3
- Contents 10
- Before You Begin 11
- Who Should Read This Manual 12
- Related Documents 13
- Using the Printer 15
- Learning About the Printers 16
- Chapter 1 — Using the Printer 17
- Understanding the Front Panel 19
- Fingerprint 21
- Understanding Printer States 23
- F1 F2 F3 F4 F5 24
- Loading Media 25
- 1 Open the media cover 31
- Printing a Test Label 33
- Creating and Printing Labels 34
- Connecting the Printer 35
- Configuring the Printer 53
- Starting point 55
- Configuring Media Settings 57
- Configuring Alerts 59
- 4 Click Submit Settings 60
- Configuring Mail Settings 62
- Configuring SNMP Settings 63
- Configuring TCP/IP Settings 64
- Configuring the Network Type 66
- Configuring 802.1x Settings 68
- Upgrading the Firmware 73
- Reference Manual 77
- (maximum 2 GB) 77
- • Troubleshooting the Printer 79
- • Adjusting the Printer 79
- • Maintaining the Printer 79
- Troubleshooting the Printer 80
- Using Dump Mode 87
- Using Testmode 88
- SELECT MEDIA 89
- 5 Lower the printhead 90
- 1234567890 91
- Clearing Media Jams 92
- Adjusting the Printhead 93
- Balance box 94
- Adjusting Printhead Pressure 95
- Adjusting Printhead Dot Line 96
- Sensor lever 99
- Point of 100
- LSS AUTO 101
- Maintaining the Printer 102
- Cleaning the Printhead 103
- Specifications 105
- Printer Specifications 106
- Print Speed and Resolution 107
- Interfaces 108
- USB Interface 109
- USB Host Interface 110
- Ethernet Interface 110
- Parallel IEEE 1284 Interface 111
- Core and Roll Specifications 112
- Non-Adhesive Strip 112
- Self-Adhesive Strip 113
- Appendix A — Specifications 114
- Self-Adhesive Labels 115
- Tickets With Gaps (Gap Stock) 117
- Accessories for the Printer 121
- Default Settings 123
- Default Configuration 124
- COM Parameters 125
- Network Parameters 125
- Test/Service Parameters 125
- Media Parameters 126
- Configuration Parameters 126
- Ser-Com “uart1:” Parameters 126
- Net-Com “net1:” Parameters 127
- Emulation Parameters 128
- Feedadjust Parameters 128
- Print Defs Parameters 128
- ESim Default Configuration 129
- Charset Paramters 131
- Date Time Paramters 131
- Appendix B — Default Settings 132
- Fingerprint Setup Menus 134
- Fingerprint Com Menu 135
- Fingerprint Network Menu 135
- Fingerprint Emulation Menu 135
- Fingerprint Feedadjust Menu 136
- Fingerprint Media Menu 136
- IPL Setup Menus 137
- IPL Network Menu 138
- IPL Test/Service Menu 138
- IPL Media Menu 139
- IPL Configuration Menu 139
- ESim Setup Menus 140
- ESim Network Menu 141
- ESim Feedadjust Menu 141
- ESim Media Menu 142
- ESim Print Defs Menu 142
- ESim Charset Menu 143
- ESim Date Time Menu 143
- Advanced Configuration 145
- Device Tree Structure 146
- Devices and Directories 146
- /rom (or rom:) 148
- /rom/images (or rom:images) 148
- /rom/secure (or rom:secure) 148
- /tmp (or tmp:) 148
- Memory and Storage 151
- *935-032-002* 162
Related products and manuals for Label printers Intermec PD41
Label printers Intermec PF2i User Manual
(194 pages)
(194 pages)
Label printers Intermec PB22 User Manual
(104 pages)
(104 pages)
Label printers Intermec PF8T Manual
(2 pages)
(2 pages)
Label printers Intermec PF8D User Manual
(92 pages)
(92 pages)
Label printers Intermec PX4I User Manual
(204 pages)
(204 pages)
Label printers Intermec PX4I User Manual
(204 pages)
(204 pages)
Label printers Intermec PF4i User Manual
(192 pages)
(192 pages)
© 2020, manymanuals.com. All rights reserved. | 0.949 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals